Template · estimating
Roofing estimate template for contractors
A usable estimate template does more than leave blanks for prices. It turns roof measurements into material quantities with the right rounding, keeps labor and disposal separate, and writes down what is allowed for and what is excluded.
Short answer
A roofing estimate template should start from the roof measurements (squares, pitch, eaves, rakes, ridges, hips, valleys, penetrations), turn them into material quantities that round up to whole units, add tear-off and installation labor adjusted for pitch, disposal and permits, apply sales tax where it applies, and list allowances and exclusions. The free spreadsheet below does this with live formulas: enter your measurements and your own prices and every quantity and total recalculates.
What the template includes
- Measurement inputs: sloped area, pitch, labor factor, layers, edge lengths, penetrations, waste and tax rate
- Material lines: shingles, underlayment, ice and water barrier, starter, hip and ridge cap, drip edge, pipe boots, nails
- Labor lines: tear-off by layer and installation, both adjusted for pitch
- Disposal and permit
- Subtotals by type, sales tax on materials and a total
- Allowances priced per unit but kept out of the total, plus exclusions and assumptions
Worked example: a 28.46-square, 6/12 roof
This is the fictional roof from our sample measurement report: 2,846 sq ft of sloped roof at 6/12, one layer to remove, 184 ft of eaves, 92 ft of rakes, 61 ft of ridges, 74 ft of hips, 38 ft of valleys and 3 pipe penetrations, with 10 percent shingle waste.
The unit prices are placeholders chosen to show the arithmetic. They are not market prices and this total is not what a roof costs. Your materials, labor rates, overhead and local requirements decide that.
| Line | Quantity | Unit price | Total |
|---|---|---|---|
| Architectural shingles | 94 bundle | $45.00 | $4,230.00 |
| Synthetic underlayment | 4 roll (10 sq) | $95.00 | $380.00 |
| Ice and water barrier | 5 roll | $110.00 | $550.00 |
| Starter strip | 3 bundle (120 lf) | $55.00 | $165.00 |
| Hip and ridge cap | 5 bundle (33 lf) | $65.00 | $325.00 |
| Drip edge | 28 piece (10 ft) | $12.00 | $336.00 |
| Pipe boots | 3 each | $25.00 | $75.00 |
| Coil nails | 2 box (7,200) | $60.00 | $120.00 |
| Tear-off labor | 32 square | $75.00 | $2,400.00 |
| Installation labor | 32 square | $150.00 | $4,800.00 |
| Dumpster and disposal | 2 load (25 sq) | $550.00 | $1,100.00 |
| Permit | 1 each | $250.00 | $250.00 |
| Materials | $6,181.00 | ||
| Labor | $7,200.00 | ||
| Disposal and permit | $1,350.00 | ||
| Sales tax on materials (6%) | $370.86 | ||
| Total | $15,101.86 |
How each quantity is calculated
Every quantity rounds up once, at the end, because suppliers sell whole bundles and rolls. Coverage per unit varies by product, so check the numbers in the template against the products you buy. Ice and water barrier assumes one 3 ft course at the eaves; where code requires the membrane to reach 24 inches inside the exterior wall, a wide overhang may need a second course.
| Line | Rule |
|---|---|
| Architectural shingles | squares × (1 + waste) × 3 bundles, rounded up |
| Synthetic underlayment | sq ft ÷ 1,000 × 1.10, rounded up |
| Ice and water barrier | (eaves × 3 ft + valleys × 6 ft) × 1.05 ÷ roll coverage, rounded up |
| Starter strip | (eaves + rakes) ÷ 120, rounded up |
| Hip and ridge cap | (ridges + hips) ÷ 33, rounded up |
| Drip edge | (eaves + rakes) ÷ 10, rounded up |
| Pipe boots | one per pipe penetration |
| Coil nails | squares × 320 ÷ 7,200, rounded up |
| Tear-off labor | squares × labor multiplier × layers, rounded up to whole squares |
| Installation labor | squares × labor multiplier, rounded up to whole squares |
| Dumpster and disposal | squares ÷ 25, rounded up |
| Permit | per local jurisdiction |
Allowances, exclusions and assumptions
The two lines that cause the most disputes are decking and extra layers, because nobody can see them from the ground. Price them per unit as allowances, outside the total, and say how you will document what you find.
Write the assumptions down: the pitch, the number of layers and the measurements the price is based on. Then list what is excluded, such as structural repairs, gutters, skylights, chimney rebuilds and interior work, unless they are separate lines.
Markup is not margin
A 30 percent markup and a 30 percent margin are different prices. On $10,000 of cost, a 30 percent markup is $10,000 × 1.30 = $13,000, which is a 23.1 percent margin. A 30 percent margin is $10,000 ÷ 0.70 = $14,285.71.
Decide which one your company means, use it the same way every time, and include overhead in your costs before you set either.
| Target | Price | Actual margin |
|---|---|---|
| 20% markup | $12,000.00 | 16.7% |
| 30% markup | $13,000.00 | 23.1% |
| 20% margin | $12,500.00 | 20.0% |
| 30% margin | $14,285.71 | 30.0% |
When a spreadsheet stops being enough
A spreadsheet works until you retype the same measurements into an estimate, a material order and a proposal. In MeasureRoofNow the reviewed roof measurement feeds assemblies and your price book, quantities round up to whole units, and the estimate becomes a proposal the homeowner can sign online.
Frequently asked questions
Is the roofing estimate template free?
Yes. The download is free and does not ask for an email address.
What format is the template?
A CSV file with live formulas. It opens in Excel, Google Sheets and LibreOffice; save it as a spreadsheet file to keep your formatting.
Are the prices in the template real?
No. They are placeholders that show how the arithmetic works. Replace every unit price with your own costs and sell prices.
Where do I get the measurements?
From a site measurement, a roof measurement report, or by tracing the roof on aerial imagery. The free roof pitch and square calculators help convert footprint area into roof area.
Last reviewed October 26, 2026. Prices and product details change; check current terms before buying. This guide is not engineering, insurance, safety or construction advice.